Type: Driver
File Name: lm3914_dotbar_33182.zip
File Size: 24.7 MB
55 (4.8)
Downloads: 35
Supported systems: Windows 2K, Windows XP, Windows Vista, Windows Vista 64 bit, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10
Price: Free* (*Free Registration Required)

Download Now


If no current flows through pin 7, then the Lm3914 dotbar display current will drop. The LED current is proportional to the current out of pin 7. No current out, no LED current. We simply have to connect the 10 LEDs to the IC, set the reference voltages for input voltage and limit the current through the LED and we are all set.

  • Dot/Bar Display Driver - LM (Linear) — Little Bird Electronics
  • Tandy - LM dot / bar display driver IC
  • Using the LM3914 Dot/Bar Display Driver IC
  • Customer Reviews
  • Dot/Bar Display Driver Hookup Guide

Lm3914 dotbar display simplified block diagram illustrates this extremely simple external circuitry. Some may wish to fit trimpots, which after alignment can be set permanently with a blob of glue. Two or more LMs can be chained together to increase the number of LEDs used to display the levels over an expanded range.

The LM is a monolithic integrated circuit that senses analog voltage levels and drives 10 LEDs, providing a linear analog display. The current drive to lm3914 dotbar display LEDs is regulated and programmable, eliminating the need for resistors. We found a 1.

You can of course have larger display range values, but a supply voltage of no more than 25 V will need to be equal to or greater than that value. Be the first to review this product. In this circuit, the R HI pin is tied to lm3914 dotbar display reference voltage output.

To calculate that voltage, knowing your two resistor values, use this equation:. It couldn't be easier.

LM3914 Dot/Bar Display Driver IC

No HTML knowledge required; even the technophobes can do it. All you need to do is copy and paste, the following code.

The water tank would certainly need some kind sensor circuit to provide an input to the LM As I said, the only limit is your imagination and I've seen some very creative applications for both the LM and Lm3914 dotbar display over the years. A high input impedance buffer operates with signals from ground to 12V, and is protected against reverse and overvoltage signals. So, if the signal voltage is near max, all LEDs should be on. In "dot" mode just a single LED is on at any time.

Dot/Bar Display Driver Hookup Guide

Connect mode directly to the power source for bar mode, and leave it floating for dot mode. These two pins can be connected to any voltage as long as it's 1. If a resistor R L is connected from that pin to ground, the current flowing through each LED will be about equal to this equation:. Here we have used 9V to power the IC to monitor an analogy voltage of V. This will show you how to set the LED currentthe divider voltageand how lm3914 dotbar display select between dot or bar display mode.

LM - Dot/Bar Display Driver

This circuit will work for both an LM and LM The only difference will be the of analog voltages required to turn on each of the LEDs. Here are a pair of diagrams that detail this simple layout. We'll assume the circuit is powered lm3914 dotbar display 5V. Heading off to Google, now Try drawing that out as a schematic, I think you'll soon spot a problem with that approach :. Customer Reviews No reviews yet. Your Account Log In Register. Someone tell me if I am way off-base with this, too. I would hate to release any of the magic blue smoke.SNVSB –JANUARY –REVISED MARCH LM Dot/Bar Display Driver. Check for Samples: LM Versatility was designed into the LM LM ACTIVE. The LM is a monolithic integrated circuit that senses analog voltage levels and drives 10 LEDs, providing a linear analog display. A single pin changes the display from a moving dot to a bar graph.


Related Drivers

Leave a Reply

Your email address will not be published. Required fields are marked *